Vi ste ovdje
Overview/Description
Cisco IPS sensors require initial and periodic (operational) management in order to perform optimally. This course provides you with configuration, verification, and troubleshooting skills that you can employ when deploying Cisco IPS device management features.
Target Audience
Anyone wishing to obtain the Cisco Certified Network Professional CCNP Security, Cisco Certified Security Professional CCSP Certification or Cisco IPS Specialist Certification designation.
Established IT professionals with a good understanding of networking and Cisco technology, installation,...
Overview/Description
A Cisco Intrusion Prevention System (IPS) sensor can be configured to provide detection or prevention capability to help defend against network attacks. Such sensors can be integrated into the network in several different ways, which require special consideration. By initializing the Cisco Intrusion Prevention System (IPS) sensor, you will configure and verify basic management and traffic forwarding capabilities of the Cisco IPS device. This course describes the available Cisco IPS sensor network integration modes, provides an analysis of their benefits and limitations...
Overview/Description
Cisco Intrusion Prevention System (IPS) sensors allow you to use multiple virtual contexts (also called virtual sensors) that allow the use of different IPS policies on different sets of inline or promiscuous interfaces. Additionally, Cisco IPS sensors are often used in environments that demand high-service availability and deterministic network performance and may require specific design decisions or configuration tuning to perform optimally. This course provides configuration guidance on Cisco IPS policy virtualization, and enables you to choose Cisco IPS network...
Overview/Description
In this module you will learn how to configure dynamic routing protocols for IPv6 routing. Topics include: -Static Routes for IPv6 -Implementing RIPng -Implementing OSPFv3 -Implementing IPv6 EIGRP -IPv6 Policy Routing -IPv6 Redistribution: RIPng -IPv6 Redistribution: RIPng and OSPF -IPv6 Redistribution: RIPng, OSPF, and BGP
Target Audience
Any student completing the ROUTE v1.0 course and preparing for the exam.
Prerequisites
None.
Expected Duration (hours)
0.1
Lesson ObjectivesCisco ROUTE 1.0 eLT: Implement RIPng, OSPFv3, EIGRP and Redistribution in IPv6
Implementing...
Overview/Description
In this module you will learn how to influence routing with policy based routing and IP SLA. Topics include: -Parallel Processes When Implementing Path Control -Procedures to Implement Path Control by Other Methods -Scenario 2: Path control using Cisco IOS IP SLA
Target Audience
Any student completing the ROUTE v1.0 course and preparing for the exam.
Prerequisites
None.
Expected Duration (hours)
0.0
Lesson ObjectivesCisco ROUTE 1.0 eLT: Implementing Path Control
Implement Path Control
Overview/Description
In this module you will gain an understanding of IPv6 address assignment and strategies used to successfully deploy IPv6 addresses in the WAN and LAN. Topics include: -Introduction to IPv6 -IPv6 Addressing Part 1 -IPv6 Addressing Part 2 -IPv6 Address Assignment Methods: Static -IPv6 Address Assignment Methods: Stateless Autoconfiguration -Unicast Connectivity on a Per-Link Basis: Point-to-Point -Unicast Connectivity on a Per-Link Basis: Point to Multipoint -Unicast Connectivity on a Per-Link Basis: Multiaccess
Target Audience
Any student completing the ROUTE v1.0...
Overview/Description
In this module you will learn about the various tunneling options for IPv6 over IPv4 and how to configure them. Topics include: -Introduction to IPv6 Transition Techniques -Manual IPv6 Tunnels -GRE IPv6 Tunnels -Automatic 6to4 Tunnels -IPv4-Compatible IPv6 Tunnels -ISATAP Tunnels
Target Audience
Any student completing the ROUTE v1.0 course and preparing for the exam.
Prerequisites
None.
Expected Duration (hours)
0.0
Lesson ObjectivesCisco ROUTE 1.0 eLT: IPv6 Transition Techniques
Implementing IPv6 Part 3
Overview/Description
In this module you will learn how to configure NAT-PT for IPv6. Topics include: -IPv6 Static NAT-PT -IPv6 Dynamic NAT-PT (Part 1) -IPv6 Dynamic NAT-PT (Part 2)
Target Audience
Any student completing the ROUTE v1.0 course and preparing for the exam.
Prerequisites
None.
Expected Duration (hours)
0.0
Lesson ObjectivesCisco ROUTE 1.0 eLT: NAT and PAT with IPv6
Implementing IPv6 Part 4
Overview/Description
In this module you will learn how to configure routing services for integration with branch office solutions such as broadband connectivity and VPN access. Topics include: -Analyzing Branch Office Designs and Planning for Branch Office Installations -Introduction to IPSec VPN -DSL Connectivity -Configuring Static Routing and NAT Verifying Existing Services -Verifying and Tuning IPSec VPNs -Configuring GRE Tunnels -Analyzing Mobile Workers Designs and Planning for Mobile Workers Installations
Target Audience
Any student completing the ROUTE v1.0 course and preparing for...
Overview/Description
The use of BGP as a routing protocol within the enterprise network requires that an administrator understand how to properly configure BGP for scalable internetworking. BGP is used in performing policy-based routing and in order to manipulate the best paths chosen by BGP, a network administrator must understand the different attributes that BGP uses and how BGP selects the best path based on these attributes. This course covers BGP configuration and verification when connecting an enterprise network to ISP networks. The BGP path selection process and attributes, their...
Koraci do učenja
Prijavite se, a ako nemate korisničko ime, registrirajte se.
Pronađite edukacijske programe u Katalogu i Certifikaciji, ili koristite polje za pretragu.
Upisani programi dostupni su u meniju Korisnik, Moji tečajevi.
Trebate pomoć?
- Česta pitanja - FAQ
- telefon: +385 1 6558 440
- email: support@cognita.hr
- Kontakt forma
